MinarcMig Adaptive 180 Manual de Serviço

MinarcMigAdaptive 180Operating manual • EnglishKäyttöohje • SuomiBruksanvisning • SvenskaBruksanvisning • NorskBrugsanvisning • DanskGebrauchsanweisun

ENShielding gas The shielding gas used for steel wires is carbon dioxide or a mixture of argon and carbon dioxide which replaces air in the arc’s area

EN2.5 FILLER WIRE The machine is delivered with the welding gun connected to +pole making it suitable for steel solid wire, stainless steel wire and

EN2.5.2 Threading the ller wire 1. Open the reel housing by pressing on the opening button and install the wire reel in such a way that it rotates

ENNOTE! When driving the wire in to the gun, do not point the gun at yourself or others or put, for example, your hand in front of the tip, because t

EN2.6 CONTROLS AND INDICATOR LIGHTS4.5.6.2.1.7.3.1. Welding power control (automatic mode) OR Wire feed speed control (manual mode) 2. Arc length t

ENWhen you switch the machine on, a green standby light switches on. Simultaneously, the main switch indicator light switches on. If the machine overh

ENdisplay during welding. The last used values remain on the display until welding is restarted or settings are changed. When adjusting the arc length

ENOnce the arc has been trimmed, it usually does not need to be changed when the welded sheet thickness changes. 2.6.4 Display in manual mode 1. Ope

EN2.7 THREADING THE SHOULDER STRAPThe machine is delivered with a shoulder strap which helps carrying the machine. Thread the shoulder strap in place

EN3. SERVICE When servicing the machine, its utilization degree and environmental circumstances should be taken into account. If you use the machine

ENCleaning the wire guide Pressure of the feed rolls remove metal dust from the ller wire’s surface which then nds its way to the wire guide. If the

EN3.3 DISPOSALDo not dispose of electrical equipment with normal waste!In observance of European Directive 2002/96/EC on waste electrical and electro

EN5. ORDERING NUMBERSProduct Ordering numberMinarcMig™ Adaptive 180(includung gun, cables, gas hose and shoulder strap)6108180Welding gun MMG20 (3 m)

EN6. TECHNICAL DATAMinarcMig™ Adaptive 180Connection voltage1 ~ 230 V ±15%, 50/60 HzRated power• 25% ED8.6kVA180A• 60% ED5.3kVA120A• 100% ED4.2

ENTemperature classH(180°C)/F(155°C)External dimensions LxWxH400x180x340mmWeight (incl. gun and cables 3,0 kg)9.8kgOperating temperature

EN23MinarcMig 180 / © Kemppi Oy / 1117

KEMPPI OYHennalankatu39PL 13FIN-15801LAHTIFINLANDTel+358389911Telefax+3583899[email protected] myynti:Tel+358389

ENOPERATING MANUALEnglishMinarcMig 180 / © Kemppi Oy / 1117

ENCONTENTS1. PREFACE ... 31.1 General ..

EN1. PREFACE1.1 GENERALCongratulations on choosing the MinarcMig equipment. Used correctly, Kemppi products can signicantly increase the productivi

ENYou can also use steel wire (solid or cored wire), stainless steel wire or aluminium wire as ller wire in the machine. The steel wire can be 0.6 mm

EN2. MACHINE USE The machine is delivered ready for operation without adjustments with 0.8 mm diameter ller wire. If you use dierent thickness ll

EN2.2 GENERAL VIEW OF THE MACHINE1. Welding gun 2. Earthing cable 3. Main switch 4. Supply voltage cable 5. Shielding gas hose connector 2.3 DI

ENThe machine can also be used with a generator. The minimum power for the generator is 4.2 kVA, and the recommended power 8.0 kVA in order for the ma